While the bar connector is out, however, asbestos should be packed in back of it to prevent this occurrence, which may be a serious affair.
Without warning a connector at the panel lit up with a coruscating orange color.
In less than a second, the damage shot through the connector and came to where it entered the computer terminal.
The tip contact is usually of brass and is connected to a slender steel rod which runs through the center of the plug and terminates near the rear end of the plug in a connector for the tip conductor of the cord.
A handle of tough fiber tubing is fitted over the rear end of the plug and this also serves to close the opening formed by cutting away a portion of the plug shell, thus exposing the connector for the tip conductor.
Only insofar as I held the endotracheal connector in place into the tracheotomy tube.
President Kennedy still had an endotracheal tube, an oro-tracheal tube in place, and the connector from this to the Bird respirator was removed.
The connector rests upon the upper race of the collar, and also helps to hold it down in its proper position.
Having drilled holes in both ends of connector, heat connector with soft flame until compound adhering to it becomes soft.
Connector drilled to correct depth] (a) Be sure that the hole is exactly over the center of the post.
Make each hole just deep enough so that the connector will come off easily.
Use long connector between end cells of upper and lower shelves.
Then drill down about half way through the connectors and terminals until you cut through the part of the connector which is welded to the post.
When you can see a seam between the post and connector you have drilled through the welded part.
Take a hot putty knife and cut the compound from the top of each of the inter-cell connectors until the entire top of the connector is exposed.
In order to prevent any mechanical strain on the leads being transmitted to the motor windings, the terminal cables are clamped in insulated bushings with a connector for each cable.
The connector in a ten-thousand-line system is the recipient of the impulses resulting from the third and fourth movements of the subscriber's dial.
The rotary switch now disconnects the tens register and starts the cylinder brushes of the primary connector which automatically stop when they encounter the calling line.
The connector shaft stops for an instant on the contacts of this busy line and immediately there follows over the rotary side of the line the inevitable single rotary impulse.
This operates the rotary and the vertical relays on the connector simultaneously and brings together for the first time the springs 21 and 22 of Fig.
Considering this circuit in respect to its action on the connector it is obvious that it energizes the release magnet on the connector which restores the connector to normal as before.
The grounded side of the battery is connected to the rotary side of his line through the third wiper of the connector and the coil 26 of the called battery supply relay.
There is no trunk to be hunted, but rather the rotary movement of the connector wipers must be made in response to the impulses, from the subscriber's station, which correspond to the units digit in the selected number.
The keys so set up determine the number of impulses that will be transmitted by the impulse-sending machine to the selector and the connector switches.
Under the present assumed condition, therefore, the connector wipers, which have been brought to the bank contacts of the desired line, will find a ground at the private bank contact.
This impulse will move the connector shaft up to the first level of bank contacts; and from now on the action of the connector differs radically from that of the selectors.
Calls coming into this sub-office over trunk lines from the main office are received on the connectors at the sub-office and the connection is made with the sub-office line by the connector in the usual manner.
For such use a given horizontal row of connectorterminals or a part of such a row is assigned to the lines leading to the private branch exchange and the connector is so modified as to have a certain "discretionary" power of its own.
D) Slip one spring connector with the attached wire upon the zinc strip, then stand the strips in the tumbler, so that they can not touch each other.
Slip a spring connector attached to wire 1 upon the iron strip I, a short distance from its end.
B) Remove the connector from Cu, swing it over into the position of the dotted line (Fig.
Hold the left-hand end of I firmly in one hand, and with the other hold the connector on wire 2 just above that on 1.
C) Remove the connector on wire 6 from Y to M, thus cutting one pair out of the circuit.
The essential points of a good connector are: It should grip the whole cable, thus making it unnecessary to strip the outer braid from any exposed part of the cable; and it should offer no live screws or contacts on the outside.
These conditions are fulfilled by the connector shown in Figure 205.
The wires are always working loose; projecting ends are bare, and if the connector is twisted, a short circuit results.
The connector may be located at either end of the flexible conductor or inserted in the conductor itself.
The connector is equipped with grease cups and antimonious lead washers.
In this majestic life we have the mediator, the medium or connector of the Divine and the human.
Remove taillight connector plugs from sockets and remove cable from mudguard spring clips.
Holding throttle grip in this position, move throttle lever forward against its stop (closed position) and secure control wire in connector block with clamp screw.
If throttle does not open fully when grip is turned inward, reset the control wire in the connector block to correct the adjustment.
If necessary, reset the control wire in the connector block until throttle is closed with full outward grip movement.
Connect the Cassette Recorder Cable (DIN plug on one end and three plugs on the other) to the Tape I/O connector that is located on the rear of the Expansion Interface nearest the Power Cord exits.
It connects between the Expansion Interface Tape input/output (I/O) and the TAPE connectoron the right rear of the TRS-80 Microcomputer.
Connect the Video Cable from the Video Display to the VIDEO connectoron the right rear of the TRS-80.
First connect one DC power cord (DIN connector) to the Power connector on the PCB.
A good connector plug cap, preferably with a clamp-type grip for the cord 5.
The connector or attachment plug should be of rubber or solid plastic and have a metal cord grip fastened to it.
The above list will hopefully give you a few useful examples demonstrating the appropriate usage of "connector" in a variety of sentences. We hope that you will now be able to make sentences using this word.
